DCPPE-200 dumps Dell Certified Professional certification
                     
https://www.dumpsplanet.comm/  



https://www.dumpsplanet.com

m/  

 

Page No | 1   
 

 

Dell 
DCPPE-200 EXAM 
Dell PowerEdge Professional Exam 

 

Product: Demo 

 
For More Information: 

     https://www.dumpsplanet.com/DCPPE-200-dumps

 

 
 
 
 
 
 
 


Page No | 2 

 

https://www.dumpsplanet.com/  

 
 
 
 
Question: 1 
   
An engineer is installing two PCIe NICs into an existing VRTX chassis. Node 1 has three PCIe cards assigned 
to it already. After installation, the engineer is unable to assign the two new NICs to node 1. 
What should the engineer do to assign the two PCIe NICs to node 1? 
 
A. Update the CMC firmware 
B. Power off the node 
C. Upgrade the license 
D. Reseat the NICs 
 
Answer: A     
 
Question: 2 
   
A VRTX server comes with two server modules. The customer requests to assign three PCIe Adapters per 
each server module. While performing this configuration, the engineer is unable to assign more than two 
PCIe Adapters per server module. 
What is the cause of this issue? 
 
A. The VRTX chassis came with a CMC Express License. 
B. The CMC configuration needs to be reset to the factory defaults. 
C. The VRTX chassis needs to be updated with the latest firmware. 
D. This is a limitation ofVRTX chassis. 
 
Answer: D     
 
Question: 3 
   
An engineer deploys an FX2 and plugs cables from GB1 and STK/GB2 into the management network 
switch for path and NIC redundancy. When the chassis is powered up, the management network is 
adversely affected. 
What should the engineer do to fix this issue? 
 
A. Plug the CMC Redundancy Dongle into GB1 and STK/GB2 
B. Configure a separate IP address for GB2 
C. Turn off STP on the management network switch 
D. Change the Management Port 2 setting to Redundant 
 
Answer: D     
 
Question: 4 
   
An engineer is deploying a new server node into an existing chassis for a virtualization cluster. The 
existing cluster nodes have many modified BIOS settings to meet workload needs. 
How should the engineer quickly deploy the new server node with matching BIOS settings? 
 
A. Use System Setup to configure dynamic profile settings based on workload. 
B. Use the iDRAC GUI to replicate from an existing server profile. 
C. Use the CMC Server Profiles to clone an existing server profile. 
D. Use the Lifecycle Controller to mirror a cluster member profile. 
 


Page No | 3 

 

https://www.dumpsplanet.com/  

Answer: A     
 
Question: 5 
   
An engineer needs to limit the power consumption of a chassis without powering down any server nodes. 
Which step should the engineer take to perform this task? 
 
A. Use the CMC to configure the System Input Power Cap for the chassis 
B. Use the iD RAC to configure the Power Cap Policy for each server node 
C. Use the CMC to configure the Power Cap Policy for each server node 
D. Use the iD RAC to configure the System Input Power Cap for the chassis 
 
Answer: B     
 
Question: 6 
   
In VRTX the following features are enabled: 
1. Server Module Firmware Update 
2. Remote sys log 
3. iD RAC Single Sign-on. 
4. Server configuration 
5. Chassis grouping 
6. Enclosure level backup 
Which license type is required? 
 
A. CMC enterprise license 
B. CMC express license 
C. iD RAC express license 
D. iD RAC enterprise license 
 
Answer: A     
 
Question: 7 
   
An engineer is troubleshooting a blade server in an FX2s. The compute sled in SLOT 3 will NOT power on. 
The engineer has taken the server down to minimum to POST. The server still does NOT power on. The 
engineer then swaps sleds SLOT 2 and 3. The iDRAC initializes in SLOT 2 but SLOT 3 is stuck at initializing 
the iDRAC. 
What are two possible sources of the issue? (Choose two.) 
 
A. Fan board 
B. iDRAC 
C. Interposer board 
D. Midplane 
E. PCIe Switch 
 
Answer: B,E     
 
Question: 8 
   
A customer has five VRTXs in a chassis group that they need to disband. The engineer disbands the 
chassis group from the group leader, but a networking interruption prevents two of the VRTXs from 
getting the signal to leave the group. 
What should the engineer do to finish disbanding the chassis group? 
 
A. Remove the remaining members from the group leader’s Remove Members list 


Page No | 4 

 

https://www.dumpsplanet.com/  

B. Recreate the group from the group leader and disband it again 
C. Remove the group association from the group members individually 
D. Reboot the CMCs of the remaining members 
 
Answer: C     
 
Question: 9 
   
An engineer has a new blade chassis that is ¾ full. The chassis has six power supplies. The chassis at peak 
power usage needs at minimum four power supplies. Redundancy is NOT a concern. 
The engineer needs a policy to meet the current needs and provide enough power to a fully populated 
chassis. 
Which policy should the engineer choose? 
 
A. N+0 
B. N+1 
C. N+2 
D. N+N 
 
Answer: A     
 
Question: 10 
   
An engineer is running an inventory report on a VRTX chassis group for a customer. When the engineer 
views the report, the engineer notices the inventory of one of the VRTX is missing one of its nodes. 
What is the cause? 
 
A. The VRTX group member is in Chassis Power State Off since the node was inserted. 
B. The VRTX group member is disconnected from the network at the time of the report. 
C. The node’s iDRAC is unreachable from the VRTX groupleader’s CMC. 
D. The node’s iDRAC needs to have an Enterprise license installed. 
 
Answer: C     

 

 

 

 

 

 

 

 

 


Page No | 5 

 

https://www.dumpsplanet.com/  

 

THANKS FOR TRYING THE DEMO OF OUR PRODUCT 

 
Visit Our Site to Purchase the Full Set of Actual DCPPE-200 Exam Questions With Answers. 
 
 

Dumps Planet also provides you extra 20% discount on the 
purchase of DCPPE-200 exam. Use Coupon code like “dp20%” 

 

 
 

https://www.dumpsplanet.com/DCPPE-200-dumps 

 

Money Back Guarantee