TP Link Support number+1-800-891-5603


Harryjacob183

Uploaded on May 3, 2018

TP Link Support number | +1-800-891-5603 Install the Router on one PC, Adapter on the 2nd PC Sparing further dialogue, here's a quick guide of the steps I took to fix my problem and get my connection working. My upstairs computer, which is receiving a signal through its adapter: 1. Installing the Router Driver on your 1st PC: Don't install the TP Link software. Instead, save its drivers to a new folder on your desktop via the TP Link Support number (you can use the drivers included on the CD that came with the router, although the version on TP Link's website may be newer). If your router is not already installed, connect it by following the included instruction booklet. When you reboot your computer and it asks you if you'd like to install the driver, you'll have to follow the options for "Install drivers manually" and/or "Have disk" and point it to the driver folder you've downloaded to PC. Your PC will then install the drivers for your router, and that portion of this guide is complete. 2. Installing the Adapter Driver on your other PC: Now, install your adapter in your second computer, which is going to receive the signal from the router. Install the card as described in the instruction manual, but do not install the TP Link software. Instead, once again, copy the drivers to your desktop. Make sure you are using the right driver version for that particular card (for instance, be sure not to use a 4.1 driver for a 4.0 adapter card).Instantly you want to get support for the resolution of TP Link router get help from TP Link Support number Configuring the Router's Settings Your router and adapter should now be installed in their respective computers, with the most recent drivers. Now, it's time to configure your router. Go to the PC that has the router connected to it, and open up your internet browser. Visit http://192.168.1.1/ - this will open up your router configuration panel. Follow the directions below, ONLY looking at the sections I mention, and leaving everything else at its default! 1. "Setup" Tab/"Basic Setup" Sub-Tab: Set to "Automatic Configuration - DHCP." Click the radio button next to "Enable DHCP server", and make sure the "Maximum number of DHCP users" is set to a number that represents the number of computers that will be getting internet access in your home (for me, this number was set to 2). 2. "Wireless" Tab/"Basic Wireless Settings" Sub-Tab: Wireless network mode should be set to "Mixed." "Wireless Network Name" should be something you can remember - maybe your first name and last initial...this is a very important part that you'll have to reference later! Lastly, set "Wireless SSID Broadcast" to Enable.The adapter version should be on a label right on the card itself 3. "Wireless" Tab/"Wireless Security" Sub-Tab: This part is entirely up to you. Personally, I'm using "WEP" mode, because I have an iPod Touch which connects to a wi-fi internet connection, and it only recognizes WEP at 128 Bits. There's nothing wrong with using this, so try it out as you follow this tutorial - you can always go back and change it to something else, like "WPA Personal." As for a passphrase, create a password -- this is the 2nd most important thing you'll have to reference later on. Click "Generate." The password will generate 4 "Keys", you'll only need to look at "Key 1" later. 4. "Wireless" Tab/"Wireless MAC Filter" Sub-Tab: Set "Wireless Mac Filter" to "Enable." Under "Permit Only," choose "Permit only PCs listed to access the wireless network" (this disallows your next door neighbor from stealing your wireless cable connection!). Now, go to your 2nd PC, with the adapter card in it. Click "Start" and "Run" in MS Windows. Type CMD and hit Enter, which will bring up a DOS prompt. Type ipconfig /all, and look for a MAC address (it will be called a "Physical address" on the list, and will look something like "01-A2-B3-E4-23-B5". Write this down. Go back to the PC with the router connected to it, which has the router configuration screen open. Make sure you're still on the screen under the "Wireless" Tab/"Wireless MAC Filter" tab, and click "Edit Mac Filter List". Type in the MAC address/Physical address that you've written down from the other PC, just a few seconds ago, anywhere on the pop up list (MAC 01 is fine). Make sure you use the correct format with the colons, don't use dashes. In other words, it should look something like 01:A2:B3:E4:23:B5 ...click "Save settings." Keywords:- TP Link Tech Support Number, TP Link Toll Free Number, TP Link Customer Care, TP Link Support number, TP Link Support, TP Link Customer support Number, TP Link Customer care number, Support for TP Link routers , TP Link Customer Service For more TP Link Support number Dial at +1-800-891-5603 Actual Content Source- https://www-routersupporthelpdesk-com.blogspot.in/2017/11/tp-link-support-tp-link-router-support.html

Comments

                     

TP Link Support number+1-800-891-5603

 Contact Number - +1-800-891-5603  Email id – [email protected]  Install the Router on one PC, Adapter on the 2nd PC  Sparing further dialogue, here's a quick guide of the steps I took to fix my problem and get my connection working. My upstairs computer, which is receiving a signal through its adapter:  Actual Content Source- https://www-routersupporthelpdesk- com.blogspot.in/2017/11/tp-link-support- tp-link-router-support.html  Installing the Router Driver on your 1st PC: Don't install the TP Link software. Instead, save its drivers to a new folder on your desktop via the TP Link Support number (you can use the drivers included on the CD that came with the router, although the version on TP Link's website may be newer).  If your router is not already installed, connect it by following the included instruction booklet. When you reboot your computer and it asks you if you'd like to install the driver, you'll have to follow the options for "Install drivers manually" and/or "Have disk" and point it to the driver folder you've downloaded to PC.  Actual Content Source-  https://www-routersupporthelpdesk-com.blogspot.in/2017/11/tp-link-support-tp- link-router-support.html   Your router and adapter should now be installed in their respective computers, with the most recent drivers. Now, it's time to configure your router.  Go to the PC that has the router connected to it, and open up your internet browser. Visit http://192.168.1.1/ - this will open up your router configuration panel.  Follow the directions below, ONLY looking at the sections I mention, and leaving everything else at its default!  1. "Setup" Tab/"Basic Setup" Sub-Tab: Set to "Automatic Configuration - DHCP." Click the radio button next to "Enable DHCP server", and make sure the "Maximum number of DHCP users" is set to a number that represents the number of computers that will be getting internet access in your home (for me, this number was set to 2).  2. "Wireless" Tab/"Basic Wireless Settings" Sub-Tab: Wireless network mode should be set to "Mixed." "Wireless Network Name" should be something you can remember - maybe your first name and last initial...this is a very important part that you'll have to reference later! Lastly, set "Wireless SSID Broadcast" to Enable.The adapter version should be on a label right on the card itself  Actual Content Source- https://www-routersupporthelpdesk-com.blogspot.in/2017/11/tp-link-support-tp- link-router-support.html  3. "Wireless" Tab/"Wireless Security" Sub-Tab: This part is entirely up to you. Personally, I'm using "WEP" mode, because I have an iPod Touch which connects to a wi-fi internet connection, and it only recognizes WEP at 128 Bits. There's nothing wrong with using this, so try it out as you follow this tutorial - you can always go back and change it to something else, like "WPA Personal."  As for a passphrase, create a password -- this is the 2nd most important thing you'll have to reference later on. Click "Generate." The password will generate 4 "Keys", you'll only need to look at "Key 1" later.  4. "Wireless" Tab/"Wireless MAC Filter" Sub-Tab: Set "Wireless Mac Filter" to "Enable." Under "Permit Only," choose "Permit only PCs listed to access the wireless network" (this disallows your next door neighbor from stealing your wireless cable connection!). Now, go to your 2nd PC, with the adapter card in it. Click "Start" and "Run" in MS Windows. Type CMD and hit Enter, which will bring up a DOS prompt. Type ipconfig /all, and look for a MAC address (it will be called a "Physical address" on the list, and will look something like "01-A2-B3-E4-23-B5". Write this down.  Go back to the PC with the router connected to it, which has the router configuration screen open. Make sure you're still on the screen under the "Wireless" Tab/"Wireless MAC Filter" tab, and click "Edit Mac Filter List". Type in the MAC address/Physical address that you've written down from the other PC, just a few seconds ago, anywhere on the pop up list (MAC 01 is fine). Make sure you use the correct format with the colons, don't use dashes. In other words, it should look something like 01:A2:B3:E4:23:B5 ...click "Save settings." TP Link Tech Support Number, TP Link Toll Free Number, TP Link Customer Care, TP Link Support number, TP Link Support, TP Link Customer support Number, TP Link Customer care number, Support for TP Link routers , TP Link Customer Service +1-800-891-5603 TP Link Customer support Number, TP Link Customer care number, Support for TP Link routers , TP Link Customer Service +1-800- 891-5603